Tsis muaj. |
Item |
Technical Specifications |
1 |
Environmental Requirements |
Operating temperature |
-40℃~55℃(-40 to +131°F) |
Storage temperature |
-45℃~70℃ (-40 to +158°F) |
Relative humidity RH |
5%~95%RH(40±2℃,no condensation) |
Atmospheric pressure |
62kPa~106kPa |
Qhov siab |
0m~2000m |
Degree of protection |
IP20 |
2 |
AC Distribution |
Input mode |
Single phase input |
Input voltage |
230Vac |
Voltage range |
90V ~ 290VAC |
Ntau zaus |
45 Hz ~ 65Hz |
System efficiency |
≥93.2% (@230Vac,Peaking) |
System input power factor |
≥0.99(@230Vac,full load) |
THD |
<5% (@230Vac,full load) |
System protection function |
AC overvoltage& under-voltage protection; DC overvoltage&under- voltage.current limit.short circuit protection; battery and rectifier over temperature protection; automatic restoration happens after the over-voltage.over-current.under-voltage and over-temperature disappear. |
3 |
DC Distribution |
System output voltage |
Rated output:48VDC |
Adjustable range: 40VDC-60VDC continuously adjustable |
System output current |
48V/150A |
System load regulation |
≤ ± 0.5% |
Kev tswj qhov system voltage |
≤ ± 0.5% |
System stability precision |
≤ ± 0.5% |
Tam sim no muaj peev xwm sib koom |
module tam sim no sib qhia tsis ntau tshaj ± 5% |
Xov tooj sib npaug hnyav lub suab nrov |
≤2mV (@230Vac,full load) |
Peak-peak suab nrov voltage |
≤ 200mV(0 MHz ~ 20MHz) (@230VAC,ib nrab load ~ puv load) |
system tam sim no txwv tus nqi |
Fais fab system: 1-165A,Nco tseg: tuaj yeem teeb tsa tsis tu ncua |
Qhov system voltage poob |
Thaum tag nrho load. qhov voltage poob ntawm DC faib nyob rau hauv lub khib yuav tsum hauv qab no 500 mV |
Kev faib tawm |
MCB xaiv tau, Default Rail Mount Terminal @ 135A * 3 |
Roj teeb faib |
MCB xaiv tau, Default Rail Mount Terminal @ 135A *1 |
4 |
Module Thiab Monitoring Unit |
Rectifier kub-swap |
Kub-swap available.not influencing system operation |
Rectifier qhia |
nrog operation.alarm.and fault indicators |
Lub sijhawm pib mos |
3s - 10s |
rectifier txhaum kev cuam tshuam |
Not influencing the set parameters of rectifier when rectifier at fault |
Remote monitoring |
With remote metering & remote control & remote signaling functions. providing standard RS485&TCP/IP Interface and 6 sets of the dry contact output port & Battery Temp.Sensor |
Monitoring unit |
English language in LCD screen of the rectifier, |
The parameters can be set through the monitoring unit. with parameter set and power-failure data store functions. Max 1000 Units vents. |
Installation method |
Rectifier module support swappable |
Remote control |
rectifier start and close.battery test. equalize and float charging ,DIN /DO configuration and so on |
Alarm functions |
With AC over voltage/under voltage.DC voltage over/under.module Communication fault and over temperature alarm,Battery remove,Surge and so on |
5 |
Safety |
Insulation resistance |
Testing voltage 500VDC, Insulation Resistance ≥10M (ib txwm atmospheric siab, qhov kub thiab txias, txheeb ze humidity <90%, tsis muaj condensation) |
Rwb thaiv tsev zog |
Input rau cov zis: 3500VDC @ 1 min&Cov dej xau tam sim no ≤10mA |
Input rau enclosures: 3500VDC @ 1 min&Cov dej xau tam sim no ≤10mA |
Tso zis rau enclosures:750VDC @ 1 min&Cov dej xau tam sim no ≤10mA |
Qhov system xau tam sim no |
≤3.5mA (230Vac input) |
Cov kev xav tau ntawm kev ua haujlwm hauv av |
Lub kaw lus nrog kev khiav hauj lwm hauv av thiab kev tiv thaiv hauv av.with meej mark.the tiv thaiv ntawm lub enclosures ntawm tis thiab tag nrho cov palpable hlau Cheebtsam thiab grounding txiv ntoo tsis ntau tshaj 0.1Ω |
AC tiv thaiv xob laim |
The equipment AC side can bear simulated lightning impulse
Current of waveform 8/20μS and rated amplitude 40kA.(xaiv tau) |
EMC |
Raws li EN55022 CLASS A,GB 9254 QIB A,FCC PART15 CLASS A,GB17626-1998, IEC 61000-3-2 |
Tsis muaj. |
Item |
Technical Specifications |
6 |
Batty |
Roj teeb qis voltage tswb thiab tiv thaiv (BLVD) |
Thaum DC voltage hauv qab lub roj teeb tiv thaiv tus nqi thiab tsis muaj AC input. lub roj teeb tiv thaiv alarm.lasting rau 1 min. roj teeb tiv thaiv DC txuas txiav tawm. |
Roj teeb tswj kev ua haujlwm |
Nrog roj teeb tswj kev ua haujlwm; nrog rau kev ua haujlwm ntawm phau ntawv lossis tsis siv neeg hloov pauv ntawm qhov sib npaug lossis ntab them raws li txoj cai ntawm lub roj teeb.tam sim no txwv kev them nyiaj ntawm lub xeev sib npaug; Kub them nyiaj rau qhov system tso zis voltage,(sib npaug thiab ntab voltage tuaj yeem hloov kho tau raws li 1 ~ 2 00 (adjustable) mV / cell / ℃.the siab dua lub roj teeb kub.the qis dua qhov ntab voltage.). |
7 |
lwm tus |
Suab nrov |
≤ 55dB (A) (ntsuas ntawm 1m deb ntawm cov khoom siv) |
MTBF |
≥ 100000 teev |
Kev cuam tshuam thiab kev vibration |
1. Tau txais kev cuam tshuam ntawm ncov acceleration 150m / s2 ntev rau 11ms |
2. tuaj yeem dais sine yoj kev vibration ntawm zaus (10 ~ 55)Hz thiab amplitude 0.35mm. |
Khoom siv hluav taws xob retardant kev ua haujlwm |
1.The flame retardant class of PCB used in system and module controller
meet V-0 cov cai ntawm GB4943. |
2.UL daim ntawv pov thawj hluav taws kub retardant cable yog saws. |
3.Cov nplaim hluav taws kub ntawm cov ntaub ntawv rwb thaiv tsev ua tau raws li V-1 cov cai ntawm UL cov cai. |
8 |
Mechanical Data |
Chassis txheej |
Lub rooj sib tham damp-proof thiab corrosion-proof requirements.muaj ib txheej txheej ntawm cov ntaub thaiv npog. uas ua tau raws li cov cai hauv qab no: |
1. Ua qhov kev xeem adhesion raws li ISO 2409. mus txog 0 chav kawm. |
2. Ua tus cwj mem hardness kuaj raws li ASTM D3363.tsis tsawg dua 2H. |
3. Ua kev cuam tshuam kev xeem raws li ASTM D2794.reaching 50kg.cm. |
4. Ua ntsev qav |
Cov khoom siv txee |
Khoom siv: CRCA ; tuab:1.5mm |
Qhov ntev (W × D × H) |
Txee: 468380mm × 132 hli (W × D × H) |
Qhov hnyav (kg) |
Appro: 18kg |